歡迎您訪問萊州聚峰機械有限公司網站!
攪拌機行業持續先行者│•☁│!
點選撥打服務熱線☁↟:400-879-1999
您的位置☁↟: 首頁 > 新聞資訊>>小型攪拌機零件氣門的順利使用方式

新聞資訊

熱銷產品

推薦新聞

  • 安全使用規範是什麼╃◕?
  • 聚峰混凝土攪拌車↟▩│▩,您的選擇│•☁│!
  • 高效作業的前提☁↟:即正確使用混凝土攪拌車
  • 聚峰帶你瞭解混凝土攪拌車的價格
  • 聚峰淺談自上料攪拌車
  • 中科聚峰廠家告訴你如何使用小型混凝土攪拌機

全國服務熱線

400-879-1999
新聞資訊 /news

小型攪拌機零件氣門的順利使用方式

來源☁↟:http://www.i1ike.com/ 日期☁↟:2022-12-02
概述☁↟:小型攪拌機零件氣門的順利使用就要多多瞭解相關的內容問題↟▩│▩,比如說為了預防氣門的損壞↟▩│▩,我們一般要知道這些方面要點☁↟: For the smooth u
小型攪拌機零件氣門的順利使用就要多多瞭解相關的內容問題↟▩│▩,比如說為了預防氣門的損壞↟▩│▩,我們一般要知道這些方面要點☁↟:
For the smooth use of the valve of small mixer parts, we need to know more about the relevant contents. For example, in order to prevent the valve from being damaged, we generally need to know the following points:
1₪·、氣門的光磨
1. Valve polishing
在攪拌機的維修中↟▩│▩,如果氣門出現燒蝕₪·、麻點及凹陷時↟▩│▩,均應進行光磨↟▩│▩,一般是在光磨機上進行↟▩│▩,作業時需要注意四個問題☁↟:一是保證氣門頭與杆部同心↟▩│▩,否則應先校直;二是光磨輛在能磨出完整的錐面的前提下是越小越好;三是儘量提高表面光潔度;四是氣門杆端部凹陷應予以磨平▩│。
During the maintenance of the mixer, if the valve is ablated, pitted or dented, it should be polished, usually on the grinder. Four problems should be paid attention to during the operation: first, ensure that the valve head is concentric with the rod, otherwise it should be straightened first; Second, the smaller the smooth grinding vehicle is, the better on the premise that it can grind a complete cone surface; Third, try to improve the surface finish; Fourth, the depression at the end of the valve stem should be smoothed.
2₪·、氣門導管的鉸銷
2. Hinge pin of valve guide
氣門杆與氣門導管配合間隙是決定氣門導管使用壽命的關鍵↟▩│▩,因此當更換新的氣門導管時↟▩│▩,鉸銷時應嚴格掌握好配合間隙↟▩│▩,使用各攪拌機車型規定間隙的下限↟▩│▩,可有效延長使用壽命▩│。
The fit clearance between the valve stem and the valve guide is the key to determine the service life of the valve guide. Therefore, when replacing a new valve guide, the fit clearance should be strictly controlled when hinge pin is used. The use of the lower limit of the specified clearance for each mixer model can effectively extend the service life.
小型攪拌機
3₪·、氣門的研磨
3. Grinding of valve
氣門的研磨分為兩種情況☁↟:一是氣門與氣門座只有輕微麻點↟▩│▩,不需要光磨和鉸銷時的研磨;二是氣門與氣門座均經過光磨和鉸銷後的研磨▩│。前者先用足金鋼砂研磨↟▩│▩,將麻點研磨掉後↟▩│▩,再用細金剛砂研磨↟▩│▩,後塗上機油研磨↟▩│▩,直至密封符合要求↟▩│▩,寬度符合規定為止▩│。後者只有密封性達不到要求時才進行研磨↟▩│▩,但操作時一定要注意↟▩│▩,不要過分用力↟▩│▩,嚴禁將氣門上下敲打↟▩│▩,否則將出現凹形砂痕↟▩│▩,影響維修質量▩│。
The grinding of valve can be divided into two situations: one is that the valve and valve seat have only slight pitting, and the grinding of smooth grinding and hinge pin is not required; The other is that the valve and valve seat are polished and reamed. The former is first ground with full emery, after the pitting is removed, it is then ground with fine emery, and then coated with oil for grinding until the sealing meets the requirements and the width meets the requirements. The latter shall be grinded only when the sealing performance fails to meet the requirements. However, care must be taken during operation to avoid excessive force. It is strictly prohibited to knock the valve up and down, or concave sand marks will appear, which will affect the maintenance quality.
小型攪拌機零件氣門的順利使用方式就講解到這裡了↟▩│▩,對此有什麼不明確的內容或者有需求↟▩│▩,就來我們網站http://www.i1ike.com做諮詢吧│•☁│!
Here is how to use the valves of small mixer parts smoothly. If you have any unclear content or need, please come to our website http://www.i1ike.com Do consulting!

截圖↟▩│▩,微信識別二維碼

免费人成黄页在线观看日本,免费男女激情视频无遮挡,JIZZXXXX18国产AV无码,厕所偷窥撒尿WCpeeingtube