社會在不斷髮展◕•·✘，用到小型攪拌機的地方也越來越多◕•·✘，在農村◕•·✘，常見的就是小型攪拌機了◕•·✘，經常使用攪拌機發生故障也是常有的事情◕•·✘，關鍵是要找到發生故障的原因₪││✘。

With the continuous development of society, there are more and more places where concrete mixers are used. In rural areas, small mixers are common, and failures of mixers are common. The key is to find the causes of failures.

1↟↟、小型攪拌機安裝平穩牢固◕•·✘，行走輪要離開地面◕•·✘，機座要高於地面₪││✘。

1. The small mixer shall be installed stably and firmly, the walking wheel shall be off the ground, and the base shall be higher than the ground.

2↟↟、小型攪拌機開機前電氣裝置良好◕•·✘，空轉執行待機械運轉正常後◕•·✘，再加料攪拌₪││✘。

2. The electrical equipment of the small mixer shall be in good condition before startup, and the materials shall be added and mixed after the machine operates normally in idle mode.

3↟↟、操作中邊加料邊加水◕•·✘，不能加入料後再啟動◕•·✘，投料不準超過額定容量₪││✘。

3. During the operation, add water while adding materials. Do not start the machine after adding materials. Feeding must not exceed the rated capacity.

4↟↟、加料量◕•·✘，工具不能碰撞攪拌機◕•·✘，更不能在運轉中把工具伸進攪拌機內扒料₪││✘。

4. The feeding amount and tools shall not collide with the mixer, and the tools shall not be put into the mixer to pick up materials during operation.

5↟↟、料斗內不能進入雜物◕•·✘，清除雜物時須停機進行₪││✘。

5. No sundries can enter the hopper, and the machine must be stopped to remove the sundries.

6↟↟、如果小型攪拌機作業中發生故障◕•·✘，應斷電停機◕•·✘，查詢原因◕•·✘，不得用工具撬動等危險方法◕•·✘，強行機械運轉₪││✘。

6. In case of failure in the operation of small mixer, power off and stop the mixer to find out the cause. Do not use tools to pry or other dangerous methods to force the mechanical operation.

7↟↟、進料口處須設定鐵棚◕•·✘，使用時不能隨意拆掉◕•·✘，拆除清理需要即時安裝好◕•·✘，工作完畢◕•·✘，要將小型攪拌機清洗乾淨◕•·✘，清理時不得使電機及電器受潮₪││✘。

7. The iron shed must be set at the feeding port, which cannot be removed at will during use. The removal and cleaning needs to be installed immediately. After the work is completed, the small mixer should be cleaned, and the motor and electrical appliances should not be affected with moisture during the cleaning.

如果有堵塞◕•·✘，就要在開機前清理₪││✘。開機的時候計量稱鬥如果是空鬥◕•·✘，顯示器上須是0◕•·✘，如果沒有顯示0◕•·✘，可以按清除鍵將數字消去₪││✘。更多相關內容就來我們網站http://www.i1ike.com諮詢吧✘◕╃！

If there is any blockage, it should be cleaned before starting the machine. When starting up, if the metering scale bucket is empty, the display must be 0. If no 0 is displayed, press the Clear key to erase the number. More relevant content will come to our website http://www.i1ike.com Consult!